Home  /   ASTM A493 PDF

Above values from ASTM A Higher strengths can be produced by heavy cold work – this may be required for certain applications. ASTM A – 16 Standard Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging. This specification covers. See the chemical composition and physical properties of ASTM A Grade annealed Stainless Steel, find alternative materials, and connect with suppliers.

Author: Megami Kigajas
Country: Botswana
Language: English (Spanish)
Genre: Medical
Published (Last): 23 June 2012
Pages: 118
PDF File Size: 3.63 Mb
ePub File Size: 17.22 Mb
ISBN: 612-3-50822-990-3
Downloads: 54849
Price: Free* [*Free Regsitration Required]
Uploader: Nikogrel

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

This abstract is a brief summary of the referenced standard. NOTE sstm typical ordering description is as follows: B Product analysis tolerance over the maximum limit for carbon and nitrogen to be 0.

Resistance to Intergranular Corrosion 8. The material shall also conform to the requirements as to mechanical properties. Link to Active This link will always route to the current Active version of the standard. The steel shall conform to the required chemical composition requirements. It is informational only and not an ast, part of the standard; the full text of the standard itself must be referred to for its use and application.

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.


ASTM A493 – 16

Current edition approved Jan. ICS Number Code For smaller sizes, similar mechanical properties apply to ferritic and martensitic grades; however the producer should be consulted regarding somewhat higher tensile properties applicable to ast grades.

Last previous edition A — A number in parentheses indicates the year of last reapproval. Packaging and Package Marking 9. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

The following lubricants may be specied: This standard has been approved for use by agencies of the Department of Defense. Historical Version s – view previous versions of standard. The SI equivalents are in parentheses and may be approximate.

This specification covers cold-finished and hot-finished stainless steel wire and wire rods for cold heading or cold forging for applications, such as fasteners, where corrosion resistance is a factor. Originally published as A — Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

An electroplated copper coating is often used. Soap is generally used.

ASTM A493 Grade 384 annealed

The producer should be consulted when material is required to tensile strength ranges other than those specied. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Your comments are axtm either for revision of this standard or for additional standards and should be addressed to ASTM Headquarters.

Most 10 Related  IZAHLI LUGET PDF

General Requirements for Delivery 4.

Copyright ASTM Standard Specication for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging1 This standard is issued under the xed designation A ; the number immediately following the designation indicates the year of original adoption or, in asm case of revision, the year of last revision.

The American Society for Testing and Materials takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Such requirements may include, but are not limited to the following: The following coatings may be specied: Material can be manufactured to tensile strength ranges other than those shown in Table 2.

ASTM A for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. All austenitic grades in the annealed condition or annealed and lightly drafted condition shall be capable of passing the criteria set by this specification. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every ve years and if not revised, either reapproved or withdrawn.